HELPLIB.HLB  —  SHOW  NETWORK
    Displays information about network services registered on a node.

    Format

      SHOW NETWORK  [network-service]

1  –  Parameter

 network-service

    Specifies a network service for which you want to display
    information.

    If you do not specify a service, the SHOW NETWORK command
    displays information about all services that are currently
    registered on the local node.

2  –  Description

    The SHOW NETWORK command displays information about network
    services available on an OpenVMS system.

3  –  Qualifiers

3.1    /FULL

    Displays all the information for the specified network service.

3.2    /OLD

    If you are running DECnet Phase IV, retains the behavior of
    the SHOW NETWORK command prior to OpenVMS Version 7.0. If the
    local node is a routing node, the /OLD qualifier provides routing
    information.

3.3    /OUTPUT

       /OUTPUT[=filespec]
       /NOOUTPUT

    Controls where the output of the command is sent. By default,
    the output of the SHOW NETWORK command is sent to the current
    SYS$OUTPUT device (usually your terminal).

    The asterisk (*)  and the percent sign (%) wildcard characters
    are not allowed in the file specification.

    If you enter the /NOOUTPUT qualifier, output is suppressed.

4  –  Examples

    1.$ SHOW NETWORK

      Product:  DECNET Node:  VADIR             Address(es):  24.365
      Product:  TCP/IP Node:  vadir.lkr.dec.com Address(es):  161.114.99.17

      This command was executed on a system running DECnet Phase V
      and TCP/IP. It indicates that the DECNET and "TCP/IP" network-
      service parameters are valid for this system.

    2.$ SHOW NETWORK "TCP/IP"

      Product: TCP/IP  Node: vadir.lkr.dec.com  Address(es):  161.114.99.17

      When the TCP/IP network-service parameter is used, it must be
      enclosed in enclosed in quotes because it contains a slash.

    3.$ SHOW NETWORK/FULL DECNET
      Product:  DECNET          Manufacturer:  VMS Sofware, Inc.
      Node:  TARPON                   Address(es):  17.51
      Network Type:  DNA IV           Interface(s):  net 0

      Node Volatile Characteristics as of  8-OCT-2009 09:15:12

      Executor node = 17.51 (TARPON)

      Identification           = VSI DECnet for OpenVMS I64
      Management version       = V4.0.0
      Incoming timer           = 45
      Outgoing timer           = 60
      Incoming Proxy           = Enabled
      Outgoing Proxy           = Enabled
      NSP version              = V4.1.0
      Maximum links            = 32
      Delay factor             = 80
      Delay weight             = 5
      Inactivity timer         = 60
      Retransmit factor        = 10
      Routing version          = V2.0.0
      Type                     = nonrouting IV
      Routing timer            = 600
      Broadcast routing timer  = 180
      Maximum address          = 1023
      Maximum circuits         = 16
      Maximum cost             = 1022
      Maximum hops             = 30
      Maximum visits           = 63
      Maximum area             = 63
      Max broadcast nonrouters = 64
      Max broadcast routers    = 32
      Maximum path splits      = 1
      Area maximum cost        = 1022
      Area maximum hops        = 30
      Maximum buffers          = 100
      Buffer size              = 576
      Default access           = incoming and outgoing
      Pipeline quota           = 4032
      Alias maximum links      = 32
      Path split policy        = Normal
      Maximum Declared Objects = 31

      Known Link Volatile Summary as of  8-OCT-2009 09:15:12

      No information in database

      Node Counters as of  8-OCT-2009 09:15:12

      Executor node = 17.51 (TARPON)

               856  Seconds since last zeroed
               471  Bytes received
               468  Bytes sent
                27  Messages received
                28  Messages sent
                 1  Connects received
                 1  Connects sent
                 0  Response timeouts
                 0  Received connect resource errors
                 2  Maximum logical links active
                 0  Aged packet loss
                 0  Node unreachable packet loss
                 0  Node out-of-range packet loss
                 0  Oversized packet loss
                 0  Packet format error
                 0  Partial routing update loss
                 0  Verification reject

      The DECNET network-service parameter is used to signify either
      DECnet Phase IV or DECnet Phase V. Use the /FULL qualifier to
      determine the DECnet phase on the node. This is an example from
      a system running DECnet Phase IV.

    4.$ SHOW NETWORK/FULL DECNET

      Product:  DECNET      Manufacturer:  VMS Software, Inc.
      Node:  VADIR          Address(es):  24.365
      Network Type:  DNA V  Interface(s):  net 0

      Node 0
      at 2002-01-16-12:50:30.528-05:00Iinf

      Identifiers

        Name                          = DEC:.XPR.VADIR
        Address                       =
          {
          (
          [ DNA_CMIP-MICE ] ,
          [ DNA_SessionControlV3 , number = 19 ] ,
          [ DNA_OSItransportV1 , 'DEC0'H ] ,
          [ DNA_OSInetwork , 49::00-18:AA-00-04-00-6D-61:21 ]
          ) ,
          (
          [ DNA_CMIP-MICE ] ,
          [ DNA_SessionControlV3 , number = 19 ] ,
          [ DNA_OSItransportV1 , 'DEC0'H ] ,
          [ DNA_OSInetwork, 49::00-18:AA-00-04-00-12-60:21
 	 (DEC:.XPR.BULEAA) ]
          ) ,
          (
          [ DNA_CMIP-MICE ] ,
          [ DNA_SessionControlV2 , number = 19 ] ,
          [ DNA_OSItransportV1 , 'DEC0'H ] ,
          [ DNA_IP , 161.114.99.17 ]
          ) ,
          (
          [ DNA_CMIP-MICE ] ,
          [ DNA_SessionControlV3 , number = 19 ] ,
          [ DNA_NSP ] ,
          [ DNA_OSInetwork , 49::00-18:AA-00-04-00-6D-61:20 ]
          ) ,
          (
          [ DNA_CMIP-MICE ] ,
          [ DNA_SessionControlV3 , number = 19 ] ,
          [ DNA_NSP ] ,
          [ DNA_OSInetwork , 49::00-18:AA-00-04-00-12-60:20 (DEC:.XPR.BULEAA) ]
          )
          }

      Status

       UID                        = 562B4000-43CF-11CF-8001-AA0004007E10
       State                      = On
       Functions Enabled          =
          {
          Address Watcher ,
          CMIP Listener
          }
       ID                         = 00-00-F8-01-FD-62

      Characteristics

       Version                    = T5.0.3
       Implementation             =
          {
          [
          Name = OpenVMS AXP ,
          Version = "V7.2-1  "
          ] ,
          [
          Name = VSI DECnet-Plus for OpenVMS ,
          Version = "V7.2-1 ECO03 31-MAY-2001 16:54:53.36"
          ]
          }
        Script Location            = <Default value>
        Maximum Listeners          = 0
        Listener Template          = <Default value>
        Secondary Names            =
          {
          }

      This example is from a system running DECnet Phase V.

    5.$ SHOW NETWORK/OLD

      OpenVMS Network status for local node 12.378 EMARET on 16-JAN-2002
     							14:46:35.64

      This is a nonrouting node, and does not have any network information.
      The designated router for EMARET is node 12.1023 A12LKR.

      The /OLD qualifier can be used only on a system running DECnet
      Phase IV.
Close Help