Opens the specified input disk image file or input master device
and records the entire contents to the specified CD-R, CD-RW,
DVD+R, and DVD+RW media formats.
Format
COPY/RECORDABLE_MEDIA source-path-name target-path-name
1 – Parameter
source-path-name
This is the data source for the recording operation.
Specify the name of a disk file containing a disk image to be
copied onto the target recording media, or the device name of the
input device containing the disk volume master for the recording.
On OpenVMS systems, this is usually a Logical Disk (LD) Utility
LDAu: device.
target-device-name
The device name of the target recordable media device.
This is usually the name of an ATAPI (DQcu:) SCSI (DKcu:), or USB
(DNcu:): CD-R/RW or DVD+R/RW recording device, or both.
2 – Description
The COPY/RECORDABLE_MEDIA command records the entire contents
of the specified input disk image file or input device onto
the media loaded into the specified output CD or DVD recording
device.
The output media format is sensed automatically, and the utility
automatically configures the recording appropriately for the
particular target device and for the output media that are
loaded.
You cannot record more than the capacity of the target media
permits. Therefore, you need to select the size of the input disk
image or the master appropriate for the capacity of the target
media. The input data source must also be an even multiple of
the sector size on optical media; the size of the input must be a
multiple of four blocks.
The recording operation is independent of the input volume
structure or input file data used for the master, and is based
solely on the block-level contents of the specified input master.
3 – Qualifiers
3.1 /BELL
Sounds an audible signal when the requested recording operation
completes successfully.
3.2 /FORMAT
/FORMAT[=keyword]
/NOFORMAT (default)
Requests that rewritable (RW) media be formatted or reformatted
prior to use. This qualifier is required for writing to blank
rewritable media or rewriting rewritable media.
If the target media cannot be formatted, this command qualifier
is ignored.
If not specified, the appropriate keyword is automatically
selected for the fastest formatting speed available for the
target recording media.
Keywords for the /FORMAT Qualifier lists available keywords.
Table 1-1 Keywords for the /FORMAT Qualifier
Keyword Function, Comments
WAIT Applies to DVD+RW. The default for the /FORMAT qualifier
is not to wait for the formatting to complete because
waiting is usually unnecessary and far slower.
Selecting WAIT causes the entire format to run
synchronously to completion before beginning the
recording operation.
The default is to:
o Operate asynchronously
o Perform background formatting
o Run both the media format operation and the recording
operations concurrently
ERASE Applies to CD-RW.
The default for the /FORMAT qualifier is to perform a
quick erasure because a full erasure is usually both
unnecessary and far slower.
Selecting ERASE causes the CD-RW rewritable disk to
be entirely erased as part of the format operation.
This erasure is performed and is completed before the
recording operation begins.
The default is to perform a quick erasure.
3.3 /LOG
/LOG (default)
/NOLOG
Shows basic device information and the progress of the recording
operation. Use /NOLOG to disable the normal output from the
utility.
3.4 /SPEED
If you must use the lower-speed or poor-quality CD recording
media, the /SPEED qualifier is often required for successful
completion of the recording process. You might need to select
a recording speed below the rated speed of the CD drive itself.
Specifically, you might need to select a recording speed that
is compatible with both the CD drive and the CD recording media
loaded in the drive.
The /SPEED qualifier accepts a single keyword for a requested
device speed:
1X
2X
4X
8X
16X
32X
MAXIMUM
The CDDVD utility attempts to match the requested speed to a
speed that the device supports. (Not all devices support all
speeds, including the lowest speed, 1X, or the highest speed
available.) The default speed is the maximum speed that the
target device supports. DVD+R/RW drives select the maximum
recording speed based on information encoded on the media.
You need to specify this qualifier only under one of the
following circumstances:
o When incompatibilities or recording errors are reported during
a previous failed recording operation.
o If the CD media in use has a rated recording speed below the
drive default recording settings.
o If CDDVD application, processor, or system I/O performance
constraints exist.
CD drives can select speeds faster than those supported by the
particular media loaded in the drive. VSI recommends that you
select only media that match the recording capabilities of the
drive. In other words, do not attempt to exceed the recording
speed limits of the particular CD media. Selecting faster media
will not make a slow drive record any faster, and selecting
faster speeds with slow media can trigger recording errors and
corrupt media.
If the recording process fails during the recording operation,
discard the write-once media and try a slower recording speed.
(Note that you can attempt to reformat and rerecord on rewritable
media.)
3.5 /VERIFY
Specifies that the contents of the output media be compared to
the contents of the input source after the recording operation.
Any data comparison errors detected are displayed.
3.6 /WRITE
/WRITE (default)
/NOWRITE
Allows you to test the system and device I/O throughput and the
command syntax without recording on the target media.
If you specify /NOWRITE and if the target drive supports the
underlying test-write hardware capability, all I/O operates as
usual although /NOWRITE disables writing to the media.
/WRITE is the default, and causes the target optical media to be
written.
4 – Examples
1.$ $ COPY/RECORDABLE_MEDIA -
$_ [/BELL] -
$_ [/DATA_CHECK=WRITE] -
$_ [/DIAGNOSTICS=(DETAILS,COMMANDS,ALL)] -
$_ [/EXTENSIONS[=(keywords)]] -
$_ [/[NO]LOG] -
$_ [/SPEED={1X|2X|4X|8X|16X|32X|MAXIMUM}] -
$_ source-path-name target-device-name
$
This example shows the generic format of the COPY/RECORDABLE_
MEDIA command.
2.$ COPY/RECORDABLE_MEDIA/FORMAT LDA1 DQA1
VSI OpenVMS CD-R/RW and DVD+R/RW Utility V1.0-3
Copyright 2015 VMS Software, Inc.
Output device vendor: HP
Output device product name: DVD Writer 740b
Commencing media format operation
Formatting may require up to an hour
Output medium format: DVD+RW
Input data being read from: LDA1:
Output data being written to: DQA1:
Input data size: 1200000 blocks
Starting operation at: 15:28:16
16 sectors written
30000 sectors written; estimated completion in 00:06:52; at 15:35:55
37000 sectors written; estimated completion in 00:06:54; at 15:36:07
46000 sectors written; estimated completion in 00:06:36; at 15:36:03
57000 sectors written; estimated completion in 00:06:08; at 15:35:51
71000 sectors written; estimated completion in 00:06:00; at 15:36:04
88000 sectors written; estimated completion in 00:05:26; at 15:35:56
110000 sectors written; estimated completion in 00:04:55; at 15:35:58
137000 sectors written; estimated completion in 00:04:12; at 15:35:56
171000 sectors written; estimated completion in 00:03:14; at 15:35:48
213000 sectors written; estimated completion in 00:02:10; at 15:35:48
266000 sectors written; estimated completion in 00:00:54; at 15:35:50
300000 sectors written; operation completed
Operation completed at: 15:35:47
Elapsed time for operation: 00:07:30
Synchronizing with output device cache
Processing completed
This example demonstrates recording the contents of LDA1:
device onto the DVD+RW media loaded into device DQA1:.