1 – ACP
Modifies the operation of the LANACP LAN Server process. Requires
SYSPRV privilege.
Format
SET ACP
1.1 – Parameters
None.
1.2 – Qualifiers
1.2.1 /ECHO
/ECHO
/NOECHO (default)
Enables partial tracing of received and transmitted downline
load messages (the first 32 bytes of the data portion of
each message). Note that the last one or two MOP messages
are displayed in full: the memory load message with cluster
parameters, and the parameter load with transfer address message,
where present in the load.
The data is written to a log file SYS$MANAGER:LAN$node-name.LOG.
To obtain the entire contents of each message, use the /FULL
qualifier as follows:
SET ACP/ECHO/FULL
1.2.2 /FULL
/FULL
/NOFULL (default)
When /ECHO is enabled, displays the entire contents of received
and transmitted downline load messages.
1.2.3 /OPCOM
/OPCOM (default)
/NOOPCOM
Enables OPCOM messages from LANACP LAN Server process.
Messages are generated by the LANACP LAN Server process when
a device status changes, load requests are received, and
loads complete. These messages are displayed on the operator's
console and included in the log file written by LANACP,
SYS$MANAGER:LAN$ACP.LOG.
1.2.4 /STOP
Stops the LANACP process. It can be restarted by reexecuting the
SYS$STARTUP:LAN$STARTUP command file.
1.3 – Example
LANCP> SET ACP/ECHO/FULL
This command enables tracing of received and transmitted
downline load messages. The /FULL qualifier displays the entire
contents of received and transmitted downline load messages.
2 – DEVICE
Sets or modifies LAN device parameters. Requires PHY_IO
privilege.
Format
SET DEVICE device-name
2.1 – Parameter
device-name
Specifies a device to be entered in the LAN volatile device
database, or whose parameters are to be modified. The device
name has the form ddcu where dd is the device code, c is the
controller designation, and u is the unit number. LAN devices are
specified as the name of the template device which is unit 0. For
example, the first DE435 Ethernet device is specified as EWA0,
the second as EWB0.
2.2 – Qualifiers (General)
2.2.1 /ALL
Sets data for all LAN devices. If you specify a device name, all
matching LAN devices are selected, for example: E to select all
Ethernet devices, F for FDDI, I for Token Ring, EW to select all
Ethernet PCI Tulip devices.
2.2.2 /DEVICE_SPECIFIC
/DEVICE_SPECIFIC=(FUNCTION="xxxx",VALUE=(n1,n2,n3...n16))
/NODEVICE_SPECIFIC
Allows some device-specific parameters to be adjusted. These
are useful for debug purposes or for experiments while doing
performance measurements. Like other LANCP commands which affect
devices, this command requires SYSPRV privilege.
Specify the negated qualifer to clear all device-specific
parameter data.
These functions are described in a text file on the system,
SYS$HELP:LAN_COUNTERS_AND_FUNCTIONS.TXT.
2.2.3 /DLL
/DLL or MOPDLL=(enable-option, exclusive-option, size-option,
knownclientsonly-option)
Provides the MOP downline load service settings for the device.
Note that defaults apply to creation of an entry in the device
database. If an existing entry is being modified, fields not
specified remain unchanged.
You can specify the following keywords with this qualifier:
o enable-option
ENABLE
DISABLE (default)
Specify ENABLE or DISABLE to indicate that MOP downline load
service should be enabled or disabled for the device.
o exclusive-option
EXCLUSIVE
NOEXCLUSIVE (default)
Specify EXCLUSIVE to indicate that no other provider of MOP
downline load service is allowed on the specified LAN device
at the same time as LANACP. Specify NOEXCLUSIVE to indicate
that the LAN MOP downline load service can coexist with other
implementations (in particular, the DECnet Phase IV and DECnet
Plus implementations that include MOP support).
Note that when you select NOEXCLUSIVE, LANACP responds only
to MOP downline load requests directed to nodes defined in the
LAN node database.
o size-option
SIZE=value
Use SIZE=value to specify the size in bytes of the file data
portion of each downline load message. The permitted range
is 246 to 1482 bytes. The default value is 246 bytes, which
should allow any client to load properly. Note that some
clients may not support the larger size.
The recommended size for better load performance and less
server overhead is the largest size that results in successful
loads of all clients. The 1482 value is derived from the
maximum packet size for CSMA/CD (Ethernet) of 1518 bytes less
the 802e header and CRC (26 bytes) and MOP protocol overhead
(10 bytes).
You can override the size on a per-node basis. See the SET
NODE commands for details.
o knownclientsonly-option
KNOWNCLIENTSONLY
NOKNOWNCLIENTSONLY (default)
Specify KNOWNCLIENTSONLY to indicate that MOP downline
load requests should be serviced only for clients defined
in the LAN permanent node database. When you select
NOKNOWNCLIENTSONLY, LANACP searches the LAN$DLL directory
for any images requested by clients that are not defined in
the LAN node database.
Note that this option is not available when NOEXCLUSIVE mode
has been selected. When NOEXCLUSIVE mode is selected, LANACP
services MOP downline load requests only for clients defined
in the LAN node database.
2.2.4 /MAX_BUFFERS
/MAX_BUFFERS=value
Sets the maximum number of receive buffers to be allocated and
used by the LAN driver for the LAN device.
2.2.5 /MIN_BUFFERS
/MIN_BUFFERS=value
Sets the minimum number of receive buffers to be allocated and
used by the LAN driver for the LAN device.
2.2.6 /PERMANENT
/PERMANENT (SET DEVICE only)
Updates the device entries in the LAN volatile device database
with any data currently set in the permanent database. This
allows you to update the volatile database after changing data
in the permanent database, rather than repeating the commands for
each updated entry to apply the changes to the volatile database.
2.2.7 /TAG
/TAG=value
Specifies the IEEE 802.1Q tag for the VLAN device.
value is the IEEE 802.IQ tag number.
2.2.8 /TRACE
/TRACE=size-option, mask-option, stop-option
/NOTRACE
Provides the LAN driver trace settings for the device. By
default, most LAN drivers do tracing of error conditions and
state changes. Tracing is controlled by an event mask that
selects the events to trace, a stop mask that specifies when
to stop tracing, and the size of the trace buffer.
You can change tracing settings at any time. The LAN driver
allocates the trace buffer from non-paged pool. You can calculate
the amount of pool needed by multiplying the number of entries by
the size of each entry, 32-bytes.
The impact of tracing on the system is negligible for error
and state change events, more significant when all events are
selected, and very significant when full packet tracing is
enabled.
The command SHOW DEVICE/TRACE displays trace results as well as
the trace mask.
You can specify the following keywords with this qualifier:
o size-option
SIZE=value
Use SIZE=value to specify the size of the trace buffer in
entries, each 32 bytes. The default is 2048 entries. The
permitted range is 256 to 1000000.
The size MOD 3 encodes the amount of packet data to include,
either 35 bytes, 66 bytes, 97 bytes, or the entire packet.
o mask-option
MASK=(value1,value2)
Use MASK=(value1,value2) to specify the trace mask to select
which type of entries should be collected in the trace
buffer. The first 32 bits consist of events common to most
LAN drivers. The second 32 bits consist of events specific to
the LAN driver for the specified device.
o stop-option
STOP=(value1,value2)
Use STOP=(value1,value2) to specify the trace mask to select
which type of entries should stop tracing. When a trace entry
is made that matches one of the bits in the stop mask, the
trace mask is cleared so that you can look at the trace data
accumulated so far.
2.2.9 /UPDATE
/UPDATE (DEFINE DEVICE only)
Adds LAN devices that are not currently in the LAN permanent
device database to that database. The initial entry for the
device uses default values for all parameters. To update the
permanent database with current information from the volatile
database, use the DEFINE DEVICE command with the /VOLATILE
qualifier. You can combine the /UPDATE and /VOLATILE qualifiers
in a single DEFINE DEVICE command.
2.2.10 /UPDATE
/UPDATE (SET DEVICE only)
Adds LAN devices that are not currently in the LAN volatile
device database to that database. The initial entry for the
device uses default values for all parameters. To update the
volatile database with current information from the permanent
database, use the SET DEVICE command with the /PERMANENT
qualifier. You can combine the /UPDATE and /PERMANENT qualifiers
in a single SET DEVICE command.
2.2.11 /VLAN_DEVICE
/VLAN_DEVICE=device-name
/NOVLAN_DEVICE
Specifies the physical LAN device that is to host the VLAN
device. The /NOVLAN_DEVICE qualifier requests deactivation of
the VLAN device.
When deactivating the VLAN device, the device-name is not
required because the VLAN driver knows which device is hosting
the VLAN device.
Note that a VLAN device cannot be deactivated if any applications
continue to use the device.
2.2.12 /VOLATILE
/VOLATILE (DEFINE DEVICE only)
Updates the device entries in the LAN permanent device database
with any data currently set in the volatile database. This allows
you to update the permanent database after changing data in the
volatile database, rather than repeating the commands for each
updated entry to apply the changes to the permanent database.
2.3 – Qualifiers (Ethernet Devices)
2.3.1 /AUTONEGOTIATE
/AUTONEGOTIATE (default)
/NOAUTONEGOTIATE
Enables or disables the use of auto-negotiation to determine the
link settings. You may need to disable link auto-negotiation
when connected to a switch or device that does support auto
negotiation.
2.3.2 /FLOW_CONTROL
/FLOW_CONTROL (default)
/NOFLOW_CONTROL
Enables flow control on a LAN device.
2.3.3 /FULL_DUPLEX
/FULL_DUPLEX
/NOFULL_DUPLEX (default)
Enables full-duplex operation of a LAN device. Before full-duplex
operation results from the use of this qualifier, additional
device or network hardware setup may be required. Some devices
may be enabled for full-duplex operation by default. Some devices
may not allow the setting to be changed.
The /NOFULL_DUPLEX qualifier disables full-duplex operation.
2.3.4 /JUMBO
/JUMBO
/NOJUMBO (default)
Enables the use of jumbo frames on a LAN device. Only Gigabit
Ethernet NICs support jumbo frames.
2.3.5 /MEDIA
/MEDIA=value
Selects the cable connection. Normally, the selection is made
during device initialization using a limited autosensing
algorithm that selects twisted pair, but fails over to AUI
(Attachment Unit Interface) if twisted pair does not appear to be
functional. Thereafter, a cabling change would require a reboot
of the system to take effect. This command allows you to change
the selection without rebooting.
Acceptable values are AUI (10Base2, 10Base5), TWISTEDPAIR
(10BaseT), and AUTOSENSE (reperform the limited autosense
algorithm). The default value is AUTOSENSE.
Some devices, such as the DE435, require a jumper change on the
Ethernet card to switch between 10Base2 and 10Base5 (thinwire and
thickwire). Other devices, such as the DE434, DE436, and DE500,
have only twisted pair connections.
2.3.6 /SPEED
/SPEED=value
Sets the speed of the LAN.
Valid values are 10, 100, 1000, 10000, or autonegotiate; the last
choice, autonegotiate, selects the 10 Mb/s for Ethernet, 100 Mb/s
for Fast Ethernet, 1000 Mb/s for Gigabit Ethernet, and 10000 Mb/s
for 10-Gigabit Ethernet. If you select autonegotiate, the LAN
driver repeats autonegotiation.
2.4 – Qualifiers (LAN Failover Devices)
2.4.1 /DISABLE
Disables the devices in a LAN Failover set. When disabled, LAN
devices can be added to or deleted from the Failover set.
2.4.2 /ENABLE
Enables a Failover set, which activates the Logical LAN device.
The LAN Failover driver selects a LAN device from the LAN
Failover set as the active device and then allows I/O to the
Logical LAN device.
2.4.3 /FAILOVER_SET
/FAILOVER_SET=(device-name[,...])
/[NO]FAILOVER_SET=(device-name[,...])
Specifies the members of a LAN Failover set.
2.4.4 /PRIORITY
/PRIORITY=value
Sets the failover priority of a LAN device. Priority is given to
the LAN failover device with the highest priority when choosing
the active LAN device. When a LAN device with a higher priority
becomes available, a failover transition to the newly available
device is performed. This allows a system manager to set a
preferred device by setting one LAN device to a higher priority
than others. The LAN failover driver uses the preferred device
when it is available.
2.4.5 /SIZE
/SIZE=value
Sets the packet size of the LAN failover device.
Valid values are STANDARD (the default) or JUMBO:
o STANDARD is the Ethernet maximum packet size of 1518 bytes.
o JUMBO is the oversize packet size available with Gigabit
Ethernet devices.
JUMBO is allowed only if all the LAN devices in the LAN
failover set are Gigabit devices.
Note that the size specified for the LAN failover device
overrides the size set on the members of the LAN failover
set; that is, the JUMBO frame setting of a LAN device is of no
consequence when the size is determined for the LAN failover
device.
2.4.6 /SWITCH
/SWITCH (SET DEVICE only)
Forces a LAN failover to another member of the LAN failover set.
You can test LAN failover operation by using this command to
switch from one device to another.
2.5 – Qualifiers (FDDI Devices)
2.5.1 /RING_PURGER
Enables the ring purger process of the FDDI device.
2.5.2 /TOKEN_ROTATION
Sets the requested token rotation time for the FDDI ring.
2.5.3 /TOKEN_TIMEOUT
Sets the restricted token timeout time for the FDDI ring.
2.5.4 /TRANSMIT_TIMEOUT
Sets the valid transmission time for the FDDI device.
2.6 – Qualifiers (Token Ring Devices)
2.6.1 /AGING_TIMER
/AGING_TIMER=value
Sets the amount of time in seconds to age Token Ring source
routing cache entries before marking them stale. This timer
expires when no traffic is sent to or received from the remote
node in this amount of time. The default value is 60 seconds.
Increase this value when idle connections bounce between the
stale and known states. Setting this value too low may cause
unnecessary explorer traffic to traverse the LAN.
2.6.2 /CACHE_ENTRIES
/CACHE_ENTRIES=value
Sets the number of entries to reserve for caching Token Ring
source routing address entries. The default value is 200 entries.
If your system directly communicates to a large number of
systems, you may want to increase this number.
2.6.3 /CONTENDER
/CONTENDER
/NOCONTENDER (default)
Specifies that the Token Ring device is to participate in
the Monitor Contention process when it joins the ring. The
/NOCONTENDER qualifier, directs the device not to challenge the
current ring server.
2.6.4 /DISCOVERY_TIMER
/DISCOVERY_TIMER=value
Sets the number of seconds to wait for a reply from a remote node
when performing the source Token Ring routing route discovery
process. The default value is 2 seconds.
If you have nodes that respond slowly on your extended LAN, you
may need to increase this number to reduce the amount of explorer
traffic that traverses your LAN.
2.6.5 /EARLY
/EARLY (default)
/NOEARLY
Enables Early Token Release on the device. The /NOEARLY
qualifier, disables Early Token Release.
2.6.6 /MAP
/MAP=(MULTICAST_ADDRESS=address, FUNCTIONAL_ADDRESS=address)
/NOMAP=(MULTICAST_ADDRESS=address)
Maps a standard multicast address to a functional address.
Token ring devices do not support IEEE 802 standard globally
defined group addresses. They do support functional addresses. A
functional address is a locally administered group address that
has 31 possible values. Each functional address sets one bit in
the third through sixth byte of the address and bytes 1 and 2 are
03-00 (C0:00 in bit reversed format).
The /NOMAP=(MULTICAST_ADDRESS=address) qualifier, clears the
mapping established for the specified address.
Specify the functional address as follows:
o The MULTICAST_ADDRESS argument requires a standard 6-byte
multicast address.
o The FUNCTIONAL_ADDRESS argument requires only the last 4
bytes of the functional address (the preceding 03-00 bytes
are automatically prefixed).
o The address variable, given as hexadecimal byte characters
separated by hyphens, specifies the canonical form of the
address. Use a colon as the separator character to indicate
the bit-reversed form of the address.
For example, to map the multicast address CB-00-01-02-03-04 to
the functional address 03-00-00-80-00-00 on the Token Ring device
IRA0, enter the following command:
SET DEVICE IRA0/MAP=(MULTI=CB-00-01-02-03-04,FUNCT=00:01:00:00)
For the default address mapping, see the following table or issue
the command SHOW DEVICE/MAP device-name.
Functional
Multicast Address Address Description
09-00-2B-00-00-04 03-00-00-00-02-00 ISO ALL ES
09-00-2B-00-00-05 03-00-00-00-01-00 ISO ALL IS
CF-00-00-00-00-00 03-00-00-08-00-00 Loopback Assistant
AB-00-00-01-00-00 03-00-02-00-00-00 DNA MOP Dump/Load
AB-00-00-02-00-00 03-00-04-00-00-00 DNA MOP Remote Console
AB-00-00-03-00-00 03-00-08-00-00-00 DNA L1 Routers
09-00-2B-02-00-00 03-00-08-00-00-00 DNA L2 Routers
09-00-2B-02-01-0A 03-00-08-00-00-00 DNA Phase IV Primary Router
AB-00-00-04-00-00 03-00-10-00-00-00 DNA Endnodes
09-00-2B-02-01-0B 03-00-10-00-00-00 DNA Phase IV Prime Unknown
Destination
09-00-2B-00-00-07 03-00-20-00-00-00 PCSA NETBIOS Emulation
09-00-2B-00-00-0F 03-00-40-00-00-00 LAT Service Advertisement
09-00-2B-02-01-04 03-00-80-00-00-00 LAT Service Solicit
09-00-2B-02-01-07 03-00-00-02-00-00 LAT Xwindown Service
Solicit
09-00-2B-04-00-00 03-00-00-04-00-00 LAST
09-00-2B-02-01-00 03-00-00-00-08-00 DNA Name Service
Advertisement
09-00-2B-02-01-01 03-00-00-00-10-00 DNA Name Service Solicit
09-00-2B-02-01-02 03-00-00-00-20-00 DNA Time Service
03-00-00-00-00-01 03-00-00-00-00-01 NETBUI Emulation
03-00-02-00-00-00 03-00-02-00-00-00 RIPL
2.6.7 /MEDIA
/MEDIA=value
Selects the type of cable media used to connect the adapter to
the Token Ring Media Access Unit (MAU) for devices that do not
automatically detect this. Acceptable values for this are either
unshielded twisted pair (UTP) or shielded twisted pair (STP). The
default value is STP.
2.6.8 /SOURCE_ROUTING
/SOURCE_ROUTING (default)
/NOSOURCE_ROUTING
Enables source routing on the Token Ring device. If you only have
one ring in your LAN or you use transparent bridging, use the
/NOSOURCE_ROUTING qualifier to turn off source routing.
2.6.9 /SPEED
/SPEED=value
Sets the speed of the Token Ring LAN.
Valid values are either 4 or 16, indicating 4 megabits per second
or 16 megabits per second. The default value for Token Ring is
16, unless the LAN adapter supports a nonvolatile mechanism for
setting this parameter.
2.6.10 /SR_ENTRY
/SR_ENTRY=(LAN_ADDRESS=address, RI=routing-information)
/NOSR_ENTRY=(LAN_ADDRESS=address)
Statically defines a specific source-routed route for a specific
node. The default value is no routes specified. This caching
remains valid while used or until the aging timer expires.
Use this qualifier only as a last resort when isolating
communication failures on extended LAN topologies.
The /NOSR_ENTRY=(LAN_ADDRESS=address) qualifier, clears the
previously defined static source routed route.
The address is a standard 6-byte LAN address (given as
hexadecimal byte characters separated by hyphens), which
specifies the canonical form of the address. Using a colon as
the separator character indicates the bit-reversed form of the
address.
The routing-information is the source routing field, specified as
a series of two-byte hexadecimal characters (each byte separated
by a hyphen). The field consists of a two-byte routing control
field followed by up to 14 two-byte segment identifiers, each
containing the ring number and the bridge number used in the hop.
2.7 – Qualifiers (ATM Devices)
2.7.1 /ATMADDRESS
/ATMADDRESS=LES sets the LAN emulation server (LES) address for
asynchronous transfer mode (ATM). Usually the address is not user
specified, and this qualifier is used only if you want a specific
address. By default the address is determined by software from
the configuration server for the LES.
The /ATMADDRESS=LES qualifier's syntax is as follows:
SET DEVICE/ATMADDRESS = ([NO]LES=the ATM server)
/ATMADDRESS=ARP sets the address resolution protocol (ARP) server
address for Classical IP over ATM. This qualifier is required
before a LIS is enabled if the local host is not the ARP server.
The /ATMADDRESS=ARP qualifier's syntax is as follows:
SET DEVICE/ATMADDRESS = (ARP=atm_arp_server)
2.7.2 /CLIP
Sets the Classical Internet Protocol (CLIP) over ATM (RFC1577).
The CLIP qualifier implements a data-link level device as a
client and/or a server in a logical IP subnet (LIS). This allows
the IP protocol to transmit Ethernet frames over the ATM network.
The /CLIP = ENABLE command causes the system to join the LIS. The
/CLIP = DISABLE command causes the client to leave the logical IP
subnet.
Note that a LIS requires a server, and there must be only one
server for each subnet. Communication between subnets can only be
performed by a router. There can only be one client for each ATM
adapter.
The /CLIP qualifier's syntax with standard Internet dotted
notation is as follows:
SET DEVICE/CLIP =(ip_subnet=a.b.c.d,
ip_address=a.b.c.d,
parent=devnam,
name="ip subnet name",
enable, disable
type = client|server)
The meanings for the syntax for /CLIP are as follows:
Option Meaning
ip_address Specifies the IP address of the CLIP
client.
ip_subnet Specifies the subnet mask of the CLIP
client.
parent=devnam Specifies the parent device name.
name Specifies a name for the LIS to aid in
operations and diagnostics.
type=client Starts up a classical IP client only. This
is the default.
type=server Starts up a classical IP server. Only one
server for each LIS is allowed, and the
server needs to be started first.
type=(server,client) Starts up a classical IP server and
client.
Keywords and their meaning for /CLIP are as follows:
Keyword Meaning
Enable Joins the logical IP subnet.
Disable Causes a client to leave the logical IP subnet.
2.7.3 /ELAN
The /ELAN qualifier has two values: enable and disable. With
/ELAN=ENABLE along with the keyword STARTUP, the LAN emulation
is loaded when LANACP starts. With /ELAN=DISABLE, the same
parameters used with ENABLE can be invoked.
The /ELAN qualifier's syntax is as follows:
DEFINE DEVICE/ELAN =(parent=parent device,
name="ELAN NAME to join",
size=1516
type=CSMACD
Enable,
Disable,
description = "description string,")
The meaning of the syntax for /ELAN is as follows:
Option Meaning
parent The ATM adapter device name. An example of the
parent device for DAPCA is: HWn0, where n is the
controller number. An example of the parent device
for DGLTA is: HCn0, where n is the controller
number.
name Optionally specified if you want to join a specific
ELAN. The default is null.
size Maximum frame size of the LAN you want to join.
Valid sizes are 1516, 4544, or 9234 bytes. The
default is 1516.
type Support currently only for CSMACD, which is the
default.
description A method of describing the ELAN for display purposes
only.
Keywords and their meanings for /ELAN are as follows:
Keyword Meaning
Enable Begins a join on a specified emulated LAN. It also loads
the driver, if not already loaded.
Disable Causes a client to leave the emulated LAN.
2.7.4 /PVC
/PVC=(vci[,...])
/[NO]PVC=(vci[,...])
Sets the permanent virtual circuit (PVC) to be used by a
Classical IP over ATM client. This is an optional qualifier.
A list of PVCs is defined for use by CLIP clients. This command
should be used before enabling the CLIP client. The PVC has to be
set up manually in the ATM switch.
The vci is the VCI (Virtual Circuit ID) of the PVC to be used.
Examples
1. LANCP> SET DEVICE/CONTENDER/MEDIA=UTP/NOEARLY/SOURCE ICA0
Enables monitor contention, UTP cable media, source routing and
disables early token release for Token Ring device ICA0.
2. LANCP> SET DEVICE/MEDIA=TWI EWB0
Sets the media type to twisted pair for the second Tulip Ethernet
device, EWB0.
3. LANCP> SET DEVICE EXA0/MOPDLL=ENABLE
Enables MOP downline load service for device EXA0, leaving the
remaining MOPDLL parameters unchanged.
4. LANCP> SET DEVICE EXA0/MOPDLL=(ENABLE,EXCLUSIVE,SIZE=1482)
Enables MOP downline load service for device EXA0, in exclusive
mode with the data transfer size of 1482 bytes, leaving the
remaining MOPDLL parameters unchanged.
5. LANCP> SET DEVICE EXA0/MOPDLL=(ENABLE,NOEXCLUSIVE)
LANCP> SET DEVICE FXA0/MOPDLL=(ENABLE,EXCL,KNOWN)
These commands enable LANACP MOP downline load service for:
o LAN device EXA0 in nonexclusive mode
o LAN device FXB0 in exclusive mode for only known clients
3 – NODE
Enters a node into the LAN volatile node database or modifies an
existing entry. Requires SYSPRV privilege.
Format
SET NODE node-name
3.1 – Parameter
node-name
Supplies the name of a node to be added to the LAN volatile node
database or an entry to be modified. Typically, the node name is
the same as that given in the system parameter SCSNODE, but it
does not need to be. The node name is limited to 63 characters in
length.
3.2 – Qualifiers
3.2.1 /ADDRESS
/ADDRESS=node-address
/NOADDRESS (default)
Associates a LAN address with the node name. Specify the address
as 6 bytes in hexadecimal notation, separated by hyphens. The
address does not have to be unique (as might be the case when the
address is not known, so a nonexistent address is specified).
If multiple node addresses are to be associated with a node name,
each combination may be given as a node name with an extension,
for example, VAXSYS.EXA for the EXA device on node VAXSYS, or
VAXSYS_1 for the first LAN device on node VAXSYS.
If you do not specify the /ADDRESS qualifier, the setting remains
unchanged. The /NOADDRESS qualifier clears the field.
3.2.2 /ALL
Defines data for all nodes in the LAN volatile node database.
If you specify a node name, all matching nodes are selected; for
example, A/ALL selects all nodes beginning with A.
3.2.3 /BOOT_TYPE
/BOOT_TYPE=boot-option
/NOBOOT_TYPE
Indicates the type of processing required for downline load
requests. You can specify one of the following keywords with
this qualifier:
o VAX_SATELLITE-a VAX satellite cluster boot
o ALPHA_SATELLITE-an Alpha satellite cluster boot
o I64_SATELLITE-an OpenVMS Cluster Integrity servers satellite
boot
o OTHER-the specified image; noncluster satellite loads that do
not require additional data
The distinction is necessary, because OpenVMS Cluster satellite
loads require additional cluster-related data be appended to the
load image given by the /FILE qualifier. The default value is
OTHER.
If you do not specify the /BOOT_TYPE qualifier, the setting
remains unchanged. The /NOBOOT_TYPE qualifier clears the field.
Note that Integrity server satellites boot using TFTP rather than
MOP services. This boot type is included so that the information
in the node database can be maintained, not because it is needed
for booting purposes.
3.2.4 /DECNET_ADDRESS
/DECNET_ADDRESS=value
/NODECNET_ADDRESS
Associates a DECnet address with the node name. Specify the
address in DECnet notation, xx.xxxx.
If you do not specify the /DECNET_ADDRESS=value qualifier, then
the setting remains unchanged. The /NODECNET_ADDRESS qualifier
clears the field.
3.2.5 /FILE
/FILE=file-spec
/NOFILE
Supplies the file name of a boot file to be used when the
downline load request does not include a file name (for example,
OpenVMS Cluster satellite booting). The file specification is
limited to 127 characters.
If no file name is specified, OpenVMS Cluster satellite loads
default to APB.EXE where the boot type is set to ALPHA and NISCS_
LOAD.EXE where the boot type is set to VAX.
If you do not specify the /FILE qualifier, the setting remains
unchanged. The /NOFILE qualifier clears the field.
3.2.6 /IP_ADDRESS
/IP_ADDRESS=value
/NOIP_ADDRESS
Associates an IP address with the node name. Specify the address
in the standard dotted notation, xxx.xxx.xxx.xxx.
If you do not specify the /IP_ADDRESS=value qualifier, the
setting remains unchanged. The /NOIP_ADDRESS qualifier clears
the filed.
3.2.7 /PERMANENT_DATABASE
/PERMANENT_DATABASE (SET NODE only)
Updates the node entries in the LAN volatile node database with
any data currently set in the permanent database. This allows
you to update the volatile database after changing data in the
permanent database, rather than repeating the commands for each
updated entry to apply the changes to the volatile database.
3.2.8 /ROOT
/ROOT=directory-specification
/NOROOT
Supplies the directory specification to be associated with the
file name. For cluster satellite service, the /ROOT qualifier
specifies the satellite root directory. For noncluster service,
this qualifier specifies the location of the file. If the file
specification or the file name given in the boot request includes
the directory name, this qualifier is ignored. The directory
specification is limited to 127 characters.
If you do not specify the /ROOT qualifier, the setting remains
unchanged. The /NOROOT qualifier clears the field.
3.2.9 /SIZE
/SIZE=value
/NOSIZE
Specifies the size in bytes of the file data portion of each
downline load message. The default is the load data size
specified for the device. The permitted range is 246 to 1482
bytes. Use a larger size for better load performance and less
server overhead.
If you do not specify the /SIZE qualifier, the setting remains
unchanged. The /NOSIZE qualifier clears the setting.
3.2.10 /V3
/V3
/NOV3
Indicates that only MOP Version 3 formatted messages are to be
used for downline load purposes, regardless of the requested
format. This allows systems to load that have a problem with MOP
Version 4 booting. This qualifier causes the requesting node to
fail over from MOP Version 4 to MOP Version 3 when no response
has been made to a MOP Version 4 load request.
If you do not specify the /V3 qualifier, the setting remains
unchanged. The /NOV3 qualifier clears the setting.
3.2.11 /VOLATILE_DATABASE
/VOLATILE_DATABASE (DEFINE NODE only)
Updates the node entries in the LAN permanent node database with
any data currently set in the volatile database. This allows
you to update the permanent database after changing data in the
volatile database, rather than repeating the commands for each
updated entry to apply the changes to the permanent database.
3.3 – Examples
1.LANCP> SET NODE VAXSYS/ADDRESS=08-00-2B-11-22-33 -
/FILE=APB.EXE -
/ROOT=$64$DIA14:<SYS10.> -
/BOOT_TYPE=ALPHA_SATELLITE
This command sets up node VAXSYS for booting as an Alpha
satellite into the cluster.
The APB.EXE file is actually located on $64$DIA14:
<SYS10.SYSCOMMON.SYSEXE>. Note that the <SYSCOMMON.SYSEXE> is
supplied by the LANACP LAN Server process and is not included
in the root definition.
2.LANCP> SET NODE VAXSYS/ADDRESS=08-00-2B-11-22-33 -
/FILE=NISCS_LOAD.EXE -
/ROOT=$64$DIA14:<SYS10.> -
/BOOT_TYPE=VAX_SATELLITE
This command sets up node VAXSYS for booting as a VAX satellite
into the OpenVMS Cluster.
The NISCS_LOAD.EXE file is actually located on $64$DIA14:
<SYS10.SYSCOMMON.SYSLIB>. The <SYSCOMMON.SYSLIB> is supplied
by the LANACP LAN Server process and is not included in the
root definition.
3.LANCP> SET NODE VAXSYS/ADDRESS=08-00-2B-11-22-33/NOROOT
This command changes the LAN address associated with node
VAXSYS and clears the current root specification.
4.SET NODE CALPAL/ADDRESS=08-00-2B-11-22-33/FILE=APB_061.EXE
This command sets up node CALPAL for booting an InfoServer
image. It defines the file that should be loaded when a load
request without file name is received from node CALPAL.
Because the file does not include a directory specification,
the logical name LAN$DLL defines where to locate the file. You
could give directory specification using the file name or by
using the /ROOT qualifier.
Note that specifying the file name explicitly in the boot
command overrides the file name specified in the node database
entry.