1    /ALL

    Displays the equivalent to specifying all the /SUMMARY, /HEADER,
    /ERROR_LOGS, /COMPRESSION_MAP, /LMB=ALL, /MEMORY_MAP, and
    /COLLECTION qualifiers.

2    /BLOCK

       /BLOCK [=m [{:|;}n] ]

    Displays a hexadecimal dump of one or more blocks. You can
    specify ranges by using the following syntax:

    no value   Displays next block
    m          Displays single block
    m:n        Displays a range of blocks from m to n, inclusive
    m;n        Displays a range of blocks starting at m and continuing
               for n blocks

3    /COLLECTION

       /COLLECTION [= {ALL|n} ]

    Displays the contents of the file identification or unwind data
    collection (on Integrity servers only) appended to a copy of the
    dump using COPY/COLLECT or written to a separate collection file
    using COLLECT/SAVE. By default, a summary of the collection is
    displayed. You can specify that the details of a single entry or
    all entries are to be displayed. n is the start block number of
    the collection entry, as displayed in the collection summary.

4    /COMPRESSION_MAP

       /COMPRESSION_MAP [=m [:n[:p[{:|;}q]]] ]

    In a compressed dump, displays details of the compression data.
    You can specify levels of detail by using the following syntax,
    where m,n,p,q may each be wildcarded (*):

    no value   Displays a summary of all compression map blocks.
    m          Displays contents of a single compression map block.
    m:n        Displays details of single compression map entry.
    m:n:p      Displays compressed and raw data for the specified
               compression section (item p in section m:n). Note that
               m:n:p may contain wildcards (*).
    m:n:p:q    Displays compressed and raw data for the specified
               range of compression sections (items p to q inclusive
               in section m:n).
    m:n:p;q    Displays compressed and raw data for the specified
               range of compression sections (q items starting from
               item p in section m:n)
 .

5    /ERROR_LOGS

    Displays a summary of the error log buffers.

6    /FILE

       /FILE = {COLLECTION | DUMP [=n]}

    If analyzing multiple dump files from a partial dump copy, or
    if a separate collection file is in use, the /FILE qualifier
    indicates whether the SHOW DUMP command applies to one of the
    dump files or to the collection file.

    If /FILE is not specified, by default, the SHOW DUMP/SUMMARY,
    SHOW DUMP/HEADER, SHOW DUMP/COLLECTION, and SHOW DUMP/ALL
    commands apply to all open files, and the SHOW DUMP/LMB=ALL and
    SHOW DUMP/COMPRESSION commands apply to all open dump files.
    If /FILE=DUMP is specified without a file number, then these
    commands apply to the primary dump file.

    By default, SHOW DUMP/BLOCK applies to the primary dump file. By
    default, SHOW DUMP/LMB=n and SHOW DUMP/COMPRESSION=n apply to the
    primary dump file or to the dump file for which the command was
    last used.

    All other qualifiers are applicable only to the primary dump
    file.

7    /HEADER

    Displays the formatted contents of the dump header.

8    /LMB

       /LMB[= {ALL|n} ]

    In a selective dump, displays the formatted contents of logical
    memory block (LMB) headers and the virtual address (VA) ranges
    within the LMB. You can specify the LMBs to be displayed by using
    the following syntax:

    no value   Displays next LMB
    n          Displays LMB at block n of the dump
    ALL        Displays all LMBs

9    /MEMORY_MAP

    In a full dump, displays the contents of the memory map.

10    /SUMMARY

    Displays a summary of the dump. This is the default.